Technical Support Please I need a support here

[Ismail-U50]

Please I need a support on a challenges am facing concerning one ASUS when I on it, it will on but not display but for like little while the battery let light blinking 3 time so I don’t know how that to do to that please kindly help.

 

[sultan321]

Please I need a support on a challenges am facing concerning one ASUS when I on it, it will on but not display but for like little while the battery let light blinking 3 time so I don’t know how that to do to that please kindly help.

replace the ram inshaAllah (by the grace of god) it will ok

 

[Ismail-U50]

replace the ram inshaAllah (by the grace of god) it will ok

It uses onboard ram, how do i go about that?

 

[sultan321]

It uses onboard ram, how do i go about that?

1st you've check with bios reprogram

 

[sultan321]

It uses onboard ram, how do i go about that?

send part number there is possible way to disconnect ram

 

[Ismail-U50]

1st you've check with bios reprogram

That is the question I initially want to ask you before you send the last message

 

[Ismail-U50]

That is the question I initially want to ask you before you send the last message

Like I want to ask you that could it be the bios?

 

[sultan321]

Like I want to ask you that could it be the bios?

most probably

 

[Ismail-U50]

send part number there is possible way to disconnect ram

For the part number

 

[sultan321]

For the part number

remove RN0501 and check

 

[sultan321]

remove RN0501 and check

you can search it from board view

 

[Ismail-U50]

you can search it from board view

After I perform the the step you give me watch the video

 

[sultan321]

After I perform the the step you give me watch the video

now once check external display

 

[Ismail-U50]

I don’t get you

 

[sultan321]

I don’t get you

please check display on vga port

 

[Ismail-U50]

please check display on vga port

Yes it display to the external monitor what could it be the issue like that please kindly Lyell to finish this work please

please check display on vg

 

[sultan321]

Yes it display to the external monitor what could it be the issue like that please kindly Lyell to finish this work please

check your lvds cable or led check 19v 5v and 3v on led

 

[Ismail-U50]

check your lvds cable or led check 19v 5v and 3v on led

Thanks you for your concern have check Voltage on the boardview through t lvds Which I could found in number 1( pin +3v is present) on the (pin 24 & 25 +3v)t is absent land which it navigate on the boardview as +3vt is present so how do I go about it. Thanks u for your support

 

[sultan321]

Thanks you for your concern have check Voltage on the boardview through t lvds Which I could found in number 1( pin +3v is present) on the (pin 24 & 25 +3v)t is absent land which it navigate on the boardview as +3vt is present so how do I go about it. Thanks u for your support

you are strongly welcome dear

 

[Madonaq]

I also have an Asus X53U
MB ver: K53U
Current flowed to the terminal and every part of the motherboard... but it's not coming up.

I've also incubated it, still the same.... whenever I plug in charger it will just blink Amber color once and nothing would happen afterwards

Thanks

 

[sultan321]

I also have an Asus X53U
MB ver: K53U
Current flowed to the terminal and every part of the motherboard... but it's not coming up.

I've also incubated it, still the same.... whenever I plug in charger it will just blink Amber color once and nothing would happen afterwards

Thanks

do same as per guideline disconnect ram

 

[Ismail-U50]

do same as per guideline disconnect ram

I just want to appreciate from you Mr. sultan with the guid line you gave me and with boardview you attach also. So I just want to tell the step line I did to make it work by the boardview. So here is it.
1. From the J1701 I try to locate the LCD line voltage of +3volt which is pin 24&25 but the +3volt was not present when I started the work
2. I traced the +3volt line down to C1724 was not present also
3.I turned back the board to locate nest line of join to C1720 +3volt was also not present.
4. Next check was U1701 which was comprises 6 leg but number 1&6 legs suppose to be present with +3volt which 1 leg was absent & leg 6 was present so what I did is I jump pass the +3volt from leg 6 to leg 1 to power the LCD. So what I did is that Mr. sultan I really appreciate Mr. sultan and other member of Dr-Bios.

 

[sultan321]

I just want to appreciate from you Mr. sultan with the guid line you gave me and with boardview you attach also. So I just want to tell the step line I did to make it work by the boardview. So here is it.
1. From the J1701 I try to locate the LCD line voltage of +3volt which is pin 24&25 but the +3volt was not present when I started the work
2. I traced the +3volt line down to C1724 was not present also
3.I turned back the board to locate nest line of join to C1720 +3volt was also not present.
4. Next check was U1701 which was comprises 6 leg but number 1&6 legs suppose to be present with +3volt which 1 leg was absent & leg 6 was present so what I did is I jump pass the +3volt from leg 6 to leg 1 to power the LCD. So what I did is that Mr. sultan I really appreciate Mr. sultan and other member of Dr-Bios.

thanks dear brother for your kind worlds my real name is adnan khalid